1. 1. Question
    When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?
    •  EIGRP authentication
  2. 2. Question
    What is the purpose of using protocol-dependent modules in EIGRP?
    •  to accommodate routing of different network layer protocols
  3. 3. Question
    If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
    •  15 seconds
  4. 4. Question
    Which statement describes a characteristic of the delivery of EIGRP update packets?
    •  EIGRP uses a reliable delivery protocol to send all update packets.
  5. 5. Question
    Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
    •  acknowledgment
  6. 6. Question
    Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
    •  01-00-5E-00-00-0A
  7. 7. Question
    What is identified within the opcode of an EIGRP packet header?
    •  the EIGRP message type that is being sent or received from a neighbor
  8. 8. Question
    An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
    •  as the autonomous system number
  9. 9. Question
    Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
    •  to exclude some interfaces from the EIGRP process
  10. 10. Question
    What information does EIGRP maintain within the routing table?
    •  only successors
  11. 11. Question
    Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors?
    •  the topology table
  12. 12. Question
    Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
    •  
    •  
    •  
    • no bandwidth
  13. 13. Question
    Which three metric weights are set to zero by default when costs in EIGRP are being calculated? (Choose three.)
    •  k2
    •  k4
    •  k5
  14. 14. Question
    A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
  15. 15. Question
    Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)
    CCNA3 v6.0 Chapter 6 Exam 003
    CCNA3 v6.0 Chapter 6 Exam 003
    •  192.168.71.0
  16. 16. Question
    A network administrator wants to verify the default delay values for the interfaces on an EIGRP-enabled router. Which command will display these values?
    •  show interfaces
  17. 17. Question
    Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
    CCNA3 v6.0 Chapter 6 Exam 002
    CCNA3 v6.0 Chapter 6 Exam 002
  18. 18. Question
    Refer to the exhibit. R2 has two possible paths to the 192.168.10.4 network. What would make the alternate route meet the feasibility condition?
    CCNA3 v6.0 Chapter 6 Exam 001
    CCNA3 v6.0 Chapter 6 Exam 001
    •  a reported distance less than 3523840
  19. 19. Question
    Which two factors does an EIGRP router use to determine that a route to a remote network meets the feasible condition and is therefore loop-free? (Choose two.)
    •  the reported distance on a neighbor router
    •  the feasible distance on the local router
  20. 20. Question
    Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
    •  The no shutdown command is required within the router configuration mode.​
  21. 21. Question
    Fill in the Blank. Use the abbreviation.
    EIGRP uses the protocol   RTP       to deliver EIGRP packets to neighbors.​
  22. 22. Question
    Fill in the blank.
    In an EIGRP topology table, a route that is in a/an     active                state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
  23. 23. Question
    Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)
    CCNA3 v6.0 Chapter 6 Exam 01
    CCNA3 v6.0 Chapter 6 Exam 01
  24. 24. Question
    Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)
    CCNA3 v6.0 Chapter 6 Exam 02
    CCNA3 v6.0 Chapter 6 Exam 02
  25. 25. Question
    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Which code is displayed on the web server?