Cisco CCNA 4 Chapter 8 version 6 Exam Answers

1. 1. Question

   When should a network performance baseline be measured?

   •  during normal work hours of an organization
   •  immediately after the main network devices restarted
   •  after normal work hours to reduce possible interruptions
   •  when a denial of service attack to the network is detected and blocked

2. 2. Question

   What is a purpose of establishing a network baseline?

   •  It provides a statistical average for network performance.
   •  It manages the performance of network devices.
   •  It creates a point of reference for future network evaluations.
   •  It checks the security configuration of network devices.

3. 3. Question

   Which three pieces of information are typically recorded in a logical topology diagram? (Choose three.)

   •  IP address and prefix lengths
   •  routing protocols
   •  static routes
   •  device models and manufacturers
   •  cable specifications
   •  device locations

4. 4. Question

   In which step of gathering symptoms does the network engineer determine if the problem is at the core, distribution, or access layer of the network?

   •  Document the symptoms.
   •  Determine the symptoms.
   •  Gather information.
   •  Determine ownership.
   •  Narrow the scope.

5. 5. Question

   A team of engineers has identified a solution to a significant network problem. The proposed solution is likely to affect critical network infrastructure components. What should the team follow while implementing the solution to avoid interfering with other processes and infrastructure?

   •  change-control procedures
   •  one of the layered troubleshooting approaches
   •  knowledge base guidelines
   •  syslog messages and reports

6. 6. Question

   Refer to the exhibit. What action occurs at stage 3 of the general troubleshooting process?

   

   CCNA4 v6.0 Chapter 8 Exam 002

   •  Correct the problem.
   •  Narrow the scope.
   •  Question end users.
   •  Document symptoms.

7. 7. Question

   After which step in the network troubleshooting process would one of the layered troubleshooting methods be used?

   •  After which step in the network troubleshooting process would one of the layered troubleshooting methods be used?
   •  determining ownership
   •  narrowing the scope
   •  gathering symptoms from suspect devices

8. 8. Question

   A network technician is troubleshooting an email connection problem. Which question to the end-user will provide clear information to better define the problem?

   •  Is your email working now?
   •  How big are the emails you tried to send?
   •  What kind of equipment are you using to send emails?
   •  When did you first notice your email problem?

9. 9. Question

   A network engineer is troubleshooting a network problem and can successfully ping between two devices. However, Telnet between the same two devices does not work. Which OSI layers should the administrator investigate next?

   •  all of the layers
   •  from the network layer to the application layer
   •  from the network layer to the physical layer
   •  only the network layer

10. 10. Question

    A network administrator is having issues with a newly installed network not appearing in other routers. At which layer of the OSI model is the network administrator going to start the troubleshooting process when using a top-down approach?

    •  application
    •  internet
    •  network
    •  session
    •  transport

11. 11. Question

    Which troubleshooting method begins by examining cable connections and wiring issues?

    •  top-down
    •  bottom-up
    •  substitution
    •  divide-and-conquer

12. 12. Question

    Refer to the exhibit. On the basis of the information presented, which two IP SLA related statements are true? (Choose two.)

    

    CCNA4 v6.0 Chapter 8 Exam 002

    •  IP SLA 99 is measuring jitter.
    •  IP SLA 99 is scheduled to begin in 2 hours.
    •  IP SLA 99 is sending echo requests every 10 seconds.
    •  IP SLA 99 is sending echo requests from IP address 192.168.2.1.
    •  IP SLA 99 is configured with the type dns target-addr 192.168.2.1 command.
    •  IP SLA 99 will run forever unless explicitly disabled.

13. 13. Question

    A company is setting up a web site with SSL technology to protect the authentication credentials required to access the web site. A network engineer needs to verify that the setup is correct and that the authentication is indeed encrypted. Which tool should be used?

    •  fault-management tool
    •  protocol analyzer
    •  baselining tool
    •  cable analyzer

14. 14. Question

    Which category of software troubleshooting tools provides device-level monitoring, configuration, and fault-management?

    •  knowledge bases
    •  baselining tools
    •  host-based protocol analyzers
    •  network management system tools

15. 15. Question

    Which two specialized troubleshooting tools can monitor the amount of traffic that passes through a switch? (Choose two.)

    •  TDR
    •  digital multimeter
    •  NAM
    •  portable network analyzer
    •  DTX cable analyzer

16. 16. Question

    Which number represents the most severe level of syslog logging?

    •  0
    •  1
    •  6
    •  7

17. 17. Question

    A user in a large office calls technical support to complain that a PC has suddenly lost connectivity to the network. The technician asks the caller to talk to nearby users to see if other machines are affected. The caller reports that several immediate neighbors in the same department have a similar problem and that they cannot ping each other. Those who are seated in other departments have connectivity. What should the technician check as the first step in troubleshooting the issue?

    •  the power outlet to the PC that is used by the caller
    •  the trunks between switches in the wiring closet
    •  the status of the departmental workgroup switch in the wiring closet
    •  the cable that connects the PC of the caller to the network jack
    •  the cable connection between a PC and a network outlet that is used by a neighbor

18. 18. Question

    A user reports that after an OS patch of the networking subsystem has been applied to a workstation, it performs very slowly when connecting to network resources. A network technician tests the link with a cable analyzer and notices that the workstation sends an excessive number of frames smaller than 64 bytes and also other meaningless frames. What is the possible cause of the problem?

    •  cabling faults
    •  corrupted NIC driver
    •  Ethernet signal attenuation
    •  corrupted application installation

19. 19. Question

    An administrator is troubleshooting an Internet connectivity problem on a router. The output of the show interfaces gigabitethernet 0/0 command reveals higher than normal framing errors on the interface that connects to the Internet. At what layer of the OSI model is the problem likely occurring?

    •  Layer 1
    •  Layer 2
    •  Layer 3
    •  Layer 4
    •  Layer 7

20. 20. Question

    A group of Windows PCs in a new subnet has been added to an Ethernet network. When testing the connectivity, a technician finds that these PCs can access local network resources but not the Internet resources. To troubleshoot the problem, the technician wants to initially confirm the IP address and DNS configurations on the PCs, and also verify connectivity to the local router. Which three Windows CLI commands and utilities will provide the necessary information? (Choose three.)

    •  arp -a
    •  ipconfig
    •  nslookup
    •  ping
    •  telnet
    •  tracert
    •  netsh interface ipv6 show neighbor

21. 21. Question

    Users report that the new web site http://www.company1.biz cannot be accessed. The helpdesk technician checks and verifies that the web site can be accessed with http://www.company1.biz:90. Which layer in the TCP/IP model is involved in troubleshooting this issue?

    •  application
    •  transport
    •  internet
    •  network access

22. 22. Question

    A networked PC is having trouble accessing the Internet, but can print to a local printer and ping other computers in the area. Other computers on the same network are not having any issues. What is the problem?

    •  The PC has a missing or incorrect default gateway.
    •  The default gateway router does not have a default route.
    •  The switch port to which the PC connects has an incorrect VLAN configured.
    •  The link between the switch to which the PC connects and the default gateway router is down.

23. 23. Question

    The newly configured ASBR that connects a company to the Internet has a default route configured and has the default-information originate command entered. Devices connected through this router can access the Internet. The problem is that no other OSPF routers have a default route in the routing table and no other users throughout the organization can access the Internet. What could be the problem?

    •  The ASBR does not have OSPF configured.
    •  The ASBR does not have an OSPF neighbor.
    •  The other routers are not configured to accept LSA type 4s.
    •  The ASBR should use the exit_interface argument instead of next-hop on the default route.

24. 24. Question

    An internal corporate server can be accessed by internal PCs, but not by external Internet users that should have access. What could be the issue?

    •  Static NAT has not been configured properly or at all.
    •  The server does not have a private IP address assigned.
    •  The default gateway router for the server does not have a default route.
    •  The switch port to which the server connects has an incorrect VLAN configured.

25. 25. Question

    Fill in the blank.
    Use the     ARP​​​     cache to verify IPv4 address to Layer 2 Ethernet address mappings on a host computer.

26. 26. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

    A user reports that PC0 cannot visit the web server http://www.server.com. Troubleshoot the network configuration to identify the problem.

    What is the cause of the problem

    •  A default route on HQ is not configured.
    •  A serial interface encapsulation is configured incorrectly.
    •  The DNS server address on PC0 is configured incorrectly.
    •  The clock rate on Branch S0/0/0 is configured incorrectly.